Dispersion and Attenuation Phenomena

From CleanEnergyWIKI
Jump to navigation Jump to search
Previous Topic Return to Optical Fibers, Waveguides, and Lasers Menu Next Topic

Dispersion and attenuation phenomena

As waves propagate they may become wider; this is known as dispersion. The amplitude of waves may decrease; this is known as attenuation. Low attenuation is critical for long distance communication fibers since reamplification of the signal is expensive and complicated. Dispersion causes an overlap of information carrying pulses which decreases the information carrying capacity of an amplitude modulated fiber. We want to design fibers that can carry a very sharp pulse with little dispersion.


Intermodal dispersion

The speed that a ray travels down a fiber depends on its internal angle q. When there are several modes at different angles then the path that each mode takes is different and the arrival time of a bit is different. The time it takes for a mode to move down a fiber:

Minimum for q ~ 90 °

Maxium for q = qc

<math>\Delta \tau_{min} = \frac {Ln_1}{ c sin 90 ^{\circ}} = \frac {Ln_1} {c}\,\!</math>
<math>\Delta \tau_{max} = \frac {Ln_1}{ c sin \theta_ c} = \frac {Ln^2_1} {cn_2}\,\!</math>

This makes sense because if the angle is 90° the mode can propagate down the center without interacting with the cladding.

The maximum difference in time of travel of two modes (one mode at 90° and one at cut-off) can be written:

<math>\Delta \tau^{SI} = \Delta \tau_{max} – \Delta \tau_{min}\,\!</math>
<math>\Delta \tau^{SI} = \frac {L} {c} \frac {n_1} {n_2} (n_1 – n_2)\,\!</math>

Thus the Dt (and therefore intermodal dispersion ) is proportional to the difference between the indices of refraction. For small fiber lengths up to 1 km the intermodal dispersion is proportional to L.

Example:

For n1 = 1.48 , n2 = 1.46 and L = 1km

<math>\Delta \tau^ {SI} = \frac {1 \times 10^3 } {1 \times 10^8} \frac {1.48} {1.46} (1.48 - 1.46)s\,\!</math>

So


<math>\Delta \tau^ {SI} = 6.76 \times 10^{-8}\,\!</math> or 68 ns

This means that for a gigabyte transfer rate after only one km there would be 70 bits that have overlapped and would be lost due to intermodal dispersion.

Over long distances the rate of dispersion reduces because of bends in the cable

At distances larger than 1km the intermodal dispersion becomes approximately proportional to the square root of the length and is a significant limiting factor.

Recoupling tends to reduce dispersion

The lower rate of increase of dispersion at longer distances is due to mode coupling. Long fibers are not perfectly straight but have small kinks or microbends. A bend acts to realign a mode by slightly changing the angle of incidence over the bended portion. This additive effect tends to recouple or reduce the dispersion of modes that had become dispersed.

Intermodal dispersion may be alleviated by either using a single mode fiber ( a fiber with a V parameter < π/2), or by designing a fiber where the mode velocities are more nearly equal as in a graded index fiber.


Graded index fibers

It is possible to build materials that have a progessively changing index of refraction over a given thickness.

For graded index fiber in which the indices of refraction of the core and cladding are very close the modal dispersion can be calculated as:

<math>\frac {\Delta \tau ^{GI}_{min}} {\Delta \tau ^ {SI}} \approx \frac {\Delta } {8} << 1\,\!</math>


With

<math>\Delta \approx \frac {n_1 – n_2} {n_1}\,\!</math>

when n1~n2

Example

For n1 = 1.48, n2= 1.46 over a distance of 1km

<math>\Delta = \frac {(1.48^2 -1.46^2)} {2 \times 1.48^2}\,\!</math> = 0.0134

Then

<math>\Delta \tau^{GI} \approx \frac {1 \times 10^3 \times 1.48} {8 \times 3 \times 10^8} (0.0134) ^2 = 1.1 \times 10^{-10}s\,\!</math>

This is approximately 600 smaller than the mode dispersion calculated for a step index fiber where

<math>\Delta \tau^{SI}= 6.7 \times 10^{-8}s\,\!</math>

Single mode Fibers

In order to achieve single mode propagation the core radius a must be:

<math>a < \frac {2.405 \lambda_0} {2\pi(n^{2}_{1} - n^{2}_{2})^{1/2}}\,\!</math>

In theory the single mode will propagate no matter how small the value of a. However, as a decreases the mode extends increasingly into the cladding, losing energy and thus being highly attenuated. Therefore it is better to keep a very close to maximum value for single mode diameter.

This can be done by making the core and cladding refractive indexes very close together. In practice single mode fibers are made with a numerical aperature (NA) of 0.1. When used with radiation that is typically used in telecommunications 1.3 μ m and 1.6 μ m, single mode fibers have core diameters between 5 μ m and 10 μ m.

Dispersion in single-mode fibers

By using single mode fibers, the problems associated with intermodal dispersion are completely avoided. However there are three other sources of dispersion; material (chromatic) dispersion, profile dispersion and waveguide dispersion.

Material dispersion arises because of the wavelength dependence of the refractive index of the fiber material. Light is never perfectly monochromatic. Any pulse of light consists of a finite spread of wavelengths that travel with a group velocity Vg given by:

<math>V_g = \frac {d \omega} {dk}\,\!</math>

where

<math>\omega = 2 \pi n\,\!</math>
<math>k=\frac { 2\pi}{\lambda}\,\!</math> and lambda is the wavelength in the material

A radiation with finite wavelength spread Δ λ 0 will have a dispersion over the length (Δ τ mat) given by

<math>\Delta \tau^{mat} \approx \frac {L \lambda^2_0}{c} \frac {d^2 n} {d \lambda^2_0} \frac {\lambda_0}{\lambda_0}\,\!</math>
Error creating thumbnail: Unable to save thumbnail to destination
Variation in the second order derivation of index refraction with respect to wavelength

The graph shows the variation in the second order derivation of index refraction with respect to wavelength.

For silica the temporal dispersion can be eliminated by using a wavelength of 1.3 μm. It is still pretty good in the range 1.3 to 1.6 which is also critical with respect to attenuation processes.

A semiconductor laser working at 1550 nm has a linewidth of 3 nm will have a Δ τ mat over 1km of 6.6 x 10-11 whereas GaAs LED operating at 850 nm and a 50 nm linewidth will have a Δ τ mat of 4.2 x 10-9. This clearly shows the superiority of lasers operating at 1550nm.

Profile Dispersion

Profile dispersion arises because of the variation of the quantity Δ with wavelength

<math>\Delta \approx \frac {n_1- n_2} {n_1}\,\!</math>

The index of refraction of different materials will respond differently to changing wavelength. In practice most fibers use silica (with slightly different dopants) for both the core and cladding so the dependence of Δ on wavelength is very small and can be ignored. This is an advantage of having n1 and n2 very close to one another.

Waveguide dispersion

Waveguide dispersion is minimal at 1.3μm and 1.4μm wavelength for Si02

Waveguide dispersion arises because the mode propagation velocity itself depends on wavelength regardless of any refractive index variation of the medium. Waveguide dispersion can not be neglected.

The graph shows both material and waveguide dispersion as a function of wavelength. Temporal dispersion is measured in units of picosecond μm -1 km -1. Dispersion remains small in the 1.3 to 1.5 μm wavelength range.

Attenuation: intrinsic fiber losses.

attenuation = :<math>\frac { 10 log _{10} (P_i / P_f)}{L} dB km ^{-1}\,\!</math>

where

<math>p_i\,\!</math> is the input power
<math>p_f\,\!</math> is the final power
<math>L\,\!</math> is length

Attenuation is expressed in decibels. This would have the unit Bells per meter, and multiplied by 10 it becomes decibels.

Intrinsic losses in silica fibers have two main sources; scattering losses and absorption losses.

Scattering losses

Fibers of silica are an amorphous materials. Crystalline materials would have diffraction losses that would quickly attenuate the beam. Scattering losses is caused by fluctuation in the refractive index through the material with each irregularity acting as point scattering center. The scale of fluctuations is in the order of λ/10. This Rayleigh scattering absorption coefficient varies as λ -4. There is a factor of 16 difference in scattering between blue light and red light. The larger the wavelength the smaller the scattering.


Absorption losses

Patterns for absorption by wavelength for SiO2

Pure silicon would have virtually no absorption in the critical wavelengths. Absorption losses in the visible and near infrared regions arise mainly from the presence of impurities such as traces of transition metal ions (eg. Fe3+ Cu2+ or hydoxyl ions (0H-). Dramatic successes in reducing fiber losses come from better control of impurity concentrations of transition metal ions. It is very difficult to eliminate OH- bonds (from Si02). These are responsible for overtones of vibration and absorption peaks at .95 μm, 0.24 μm and 1.39 μm. The dashed line is the background Rayleigh scattering. Above 1.6 μm there is a rapid increase in infrared absorption from lattice transitions. So there are two windows for absorption at 1.3 μm and 1.55 μm. Thus the combination of all scattering and attenuation phenomena can be optimized for these two wavelengths, which are the common telecommunications wavelengths. When working with a few miles, there is no need to regenerate the signal. In this case, it is beneficial to work at 1.3 μm since there is less dispersion loss. Theses are the types of compromises that engineers are looking at.

To date some of the lowest attenuations have obtained with GeO2 - doped SiO2 fibers which have attenuations of about .2 dB km-1 at 1.55 μm. This is close to the limit of Rayleigh scattering. This still is high enough that a cross Atlantic cable needs to be reamplified along the way.

Optical Fiber Materials

Optic fiber materials must satisfy certain conditions to be of practical use.

  • They must be highly transparent to the radiation being used (the telecommunication frequencies or specific wavelength for example light guides to supply pumped lasers)
  • It must be possible and efficient to fabricate the core and cladding structures.
  • It must be reasonable flexible

The two types of materials that satisfy these criteria are silica (Si02) and various plastics.

Silica fiber

Pure silica has an index of refraction that is on the order of 1.45 at one micron. Wavelengths are usually discussed in vacuum or in air; not what the wavelength becomes in the material itself. Doping is used to build up the difference in index of refraction between the core and the cladding. (the core has to have higher index of refraction than the cladding) For silica, the most common dopants are titania (TiO2), alumina, (Al2O3) or germania(GeO2), which lead to the highest index of refraction. The best fibers that have been obtained so far have Germania-doped silica for the core. Boria (B2O3) or fluorine tends to decrease the refractive index of the silica matrix so it is best to use them in the claddings. Therefore, germania-doped cores and fluorine-doped claddings are typical fibers that are being used.

The doping process can’t change the index of refraction a lot so the differences in indices between the core and the cladding are not that big. Therefore the fibers have rather small numerical apertures on the order of 0.2. Typical multimode fibers, step-index fibers, usually have diameters that are around 200 μm and a cladding that of an additional 50 μm

But besides those thick fibers, there are also single-mode fibers which must be a just a few microns so that there is just a single-mode that can propagate. When fabricating graded-index fibers by doping the core with, for example, germanium oxide, a larger concentration in the center of the core is obtained and the doping level gradually decreases towards the outside of the core. So you have the profile with a gradually decreasing index of refraction as you move from the center of the core towards its edge.

Both graded-index and single mode silica fibers are readily available. In silica fibers, besides the core and the cladding, there is also a plastic coating but it has no optical activity. It is just there to protect the cladding and the core from any chemical or physical damage.

Plastic fiber

Up until a few years ago, new types of fibers were exclusively that for local-area networks because of the usual losses; but things are changing. These new fibers are based on plastics. While in the case of silica fibers, both the core and the cladding are made essentially of silica, in plastic fibers the core and cladding is made of two different plastics. Therefore, larger numerical apertures (ie 0.4 or greater) can be obtained since larger differences in indices between the core and the cladding can be designed. Polymethyl methacrylate (PMMA, n= 1.495) is a material that is considered quite a bit for the core. Fluoroalkyl methacrylate with an index of refraction of n=1.402 can be used for the cladding. Thus, the indices have a much larger difference than in the case of silica fibers.

In those plastics, the major source of attenuation is due to overtones of C-H vibrations. There is also large Rayleigh scattering from macromolecules. However, over shorter distances, for instance local area networks (LAN) at the level of building ( a few hundred meters), much larger losses from plastic can be worked with. Plastic fiber’s can be tied in a knot without it breaking and still transmit the light guided through the fiber. As long as the optical signal is not sent too far, the fibers are very useful because of their intrinsic flexibility. For example, a car could use plastic fiber to send optical signals from the various sensors to the central computer. Plastic fibers could easily bend along the snaking path within the body.

Attenuation for plot for PMMA

There is much progress that has been done as well in terms of the quality of the fibers. This graph shows the attenuation that is typical for a PMMA fiber in terms of the core of 150-200 decibels per kilometer. Silica fibers at 1.55 micron has an attenuation of only 0.2 decibel per kilometer. The strong attenuation with PMMA is essentially due to the C-H vibrations. A number of researchers, for instance researchers in Japan have designed fibers made of derivatives of PMMA in which all the hydrogens are replaced by fluorines. Then the C-H vibrations are largely out of the range of the normal transmission wavelengths ( that is 570nm and 650 nm which are associated with red-emitting LEDs). The progress that has been made in reducing the attenuation in plastic fibers is remarkable. Now people are discussing using plastic fibers for very long distances. The goal is to move away from those C-H bonds and find new elements that can substitute the hydrogens in these plastics so that a completely different attenuation profile can be obtained.

See Wikipedia Fiber Optic Materials


Optical communications systems

An optical communication system means that there is information or a light signal that is sent somewhere by optical fiber. The goal is to modulate the signal or one of the characteristics of the signal so that the information can be obtained at the end of the line. The modulation can be made on various characteristics of the light such as variation in amplitude, irradiance or intensity (which is related to the electric field of the light), frequency, the phase of the light, and the polarization of the light. When relying on light at optical frequencies ( those on the order of visible light) modulation of the intensity (or irradiance) of signal is used.

There are two types of modulation. Either a analog signal or digital signal (analog modulation or digital modulation) can be used. A simple example that uses modulation is sending a voice signal.

Analog modulation

When you pick up the phone, the voice is first transmitted into an electrical signal which is a time varying modulation of the voltage. That signal needs to be sent to the electrical fiber in the form of a modulation of the light signal. This process can be done in an analog fashion. That input information on the electrical voltage continuously varies the parameter of intensity that is modulated for the light. In this case, at any point in time, when the voltage increases, the intensity of your light signal increases; the voltage decreases, the intensity of your light decreases. There is a one to one relationship between the original signal amplitude and the magnitude of the wave parameter (irradiance).


Digital modulation

Previous Topic Return to Optical Fibers, Waveguides, and Lasers Menu Next Topic