Difference between revisions of "Current OPV Research Directions"

From CleanEnergyWIKI
Jump to navigation Jump to search
Line 112: Line 112:


== Fabrication Processes ==
== Fabrication Processes ==
[[Image:Nanoimprinting.jpg|thumb|300px|]]
[[Image:Nanoimprinting.jpg|thumb|300px|a) Nanoimprinting process developed for organic semiconductors; b) SEM picture of nanoimprinted polycarbonate pillars 30 nm wide, 60 nm high and separated by 160 nm (center-to-center) Norwood and Peyghambarian Groups]]
There are real advantages to processing methods which could easily, reproducibly and systematically nano-texture the first-deposited donor or acceptor polymer layer in an organic solar cell (OSC), forming “nano-posts” or “nano-indentations” with optimal lengths and widths, ready for addition of the second component in a bulk heterojunction (BHJ) OSC.  As the aspect ratio of such a nanostructure increases, at least an order of magnitude increase in the interfacial area between the donor and acceptor phases is anticipated, thereby greatly enhancing exciton dissociation with retention of vectoral charge transport pathways.  Such a processing technique, if scaled to realistic device levels, would remove one of the key limitations to BHJ formation from conventional polymeric materials. Nanoimprint lithography (NIL) involves the formation of nano-posts or nanoindentations in a reusable master stamp, which is then used to emboss a freshly deposited polymer or sol-gel oxide film.  This is a process recently developed for creation of grating-like features on optical fibers and waveguides, and is now being scaled to dimensions relevant for OSC device processing.  
There are real advantages to processing methods which could easily, reproducibly and systematically nano-texture the first-deposited donor or acceptor polymer layer in an organic solar cell (OSC), forming “nano-posts” or “nano-indentations” with optimal lengths and widths, ready for addition of the second component in a bulk heterojunction (BHJ) OSC.  As the aspect ratio of such a nanostructure increases, at least an order of magnitude increase in the interfacial area between the donor and acceptor phases is anticipated, thereby greatly enhancing exciton dissociation with retention of vectoral charge transport pathways.  Such a processing technique, if scaled to realistic device levels, would remove one of the key limitations to BHJ formation from conventional polymeric materials. Nanoimprint lithography (NIL) involves the formation of nano-posts or nanoindentations in a reusable master stamp, which is then used to emboss a freshly deposited polymer or sol-gel oxide film.  This is a process recently developed for creation of grating-like features on optical fibers and waveguides, and is now being scaled to dimensions relevant for OSC device processing.  


Line 119: Line 119:
[[Image:Solvent_annealing.png|thumb|500px|TiOPc]]
[[Image:Solvent_annealing.png|thumb|500px|TiOPc]]


[[Image:Solvent_annealing_protocols.jpg|thumb|400px|a) Nanoimprinting process developed for organic semiconductors; b) SEM picture of nanoimprinted polycarbonate pillars 30 nm wide, 60 nm high and separated by 160 nm (center-to-center) Norwood and Peyghambarian Groups]]
[[Image:Solvent_annealing_protocols.jpg|thumb|400px|]]


See Armstrong <ref>N. R. Armstrong et al.,  Adv. Funct. Mater.  ; DOI: 10.1002/adfm.200801723</ref>
See Armstrong <ref>N. R. Armstrong et al.,  Adv. Funct. Mater.  ; DOI: 10.1002/adfm.200801723</ref>

Revision as of 13:29, 10 September 2009


Previous Topic Return to OPV Menu


These are promising directions in organic photovoltaic research being pursued at the CMDITR

Evolution of Solar Cell Efficiency

These are the types of efficiencies that people have been able to reach. For example, with silicon, fill factors of about 0.8 and conversion efficiency, of 24% can be reached.

The Grätzel cell, which is a hybrid cell that has both organic and inorganic components and uses a liquid electronlyge, has a conversion efficiency of about 11%. Michael Grätzel is a professor at the technical school of Lausanne in Switzerland.

With polymers, Allen Heeger has recently reported a conversion efficiency of up to 6%. Our goal at this time is to reach the 10% efficiency in organic cells. However, it does not seem to be very easy to achieve.

Characteristic Silicon Organic (Tang) Organic (Forrest) Organic (Graetzel) Polymer Hybrid nanorods
Open circuit voltage (Voc; V) 0.7 0.45 1.02 0.721 0.63 0.7
Short circuit current density (Jsc; mA/cm2) 43 2.3 9.7 20.53 9.5 5.7
Voc x Jsc (mW/cm2) 30.1 1.035 9.894 14.80213 5.985 3.99
Fill factor (FF) 0.8 0.65 0.59 0.704 0.68 0.4
Illumination intensity (mW/cm2) 100 75 100 100 80 96.4
Conversion efficiency (%) 24.08 0.9 5.7 10.4 5.1 1.7

New materials

Research directions include using multilayers of small molecules, building polymer blends with interpenetrated networks, nanostructured oxide polymers and hybird approaches using doped inorganics in an organic matrix.

Discotic Mesophase Materials

Another kind of thalocyanine that is solution processable form molecules that self-organize into columnar stacks. This the kind of configuration that makes molecules good light absorbers and good conductors.
An AFM visualization of sheets discotic materials that have been deposited on a single crystal substrate.


Dendritic Polymers

Dendritic polymers create a spiky surface which may be able to be combined with an suitable electron acceptor layer to form a finely organized heterojunction.


Nanoparticles

Quantum dot compounds can be can be used as part of the donor or acceptor materials.
Semiconductor nanoparticles built from cadmium selenide 2-5nm in diameter take on interesting electron properties. The particle is capped with ligands to make them processable. The size of the nanoparticle determines the luminescence. The smallest make blue color, the largest makes the red. Used in a solar cell they absorb in the same color ranges.


Tailored interfaces

New hybrid materials could be used to build a solar cell step by step. Light absorbing rods are placed on a transparent base. Then the electron transport rods, and the hole blocking layer.



Fabrication Processes

a) Nanoimprinting process developed for organic semiconductors; b) SEM picture of nanoimprinted polycarbonate pillars 30 nm wide, 60 nm high and separated by 160 nm (center-to-center) Norwood and Peyghambarian Groups

There are real advantages to processing methods which could easily, reproducibly and systematically nano-texture the first-deposited donor or acceptor polymer layer in an organic solar cell (OSC), forming “nano-posts” or “nano-indentations” with optimal lengths and widths, ready for addition of the second component in a bulk heterojunction (BHJ) OSC. As the aspect ratio of such a nanostructure increases, at least an order of magnitude increase in the interfacial area between the donor and acceptor phases is anticipated, thereby greatly enhancing exciton dissociation with retention of vectoral charge transport pathways. Such a processing technique, if scaled to realistic device levels, would remove one of the key limitations to BHJ formation from conventional polymeric materials. Nanoimprint lithography (NIL) involves the formation of nano-posts or nanoindentations in a reusable master stamp, which is then used to emboss a freshly deposited polymer or sol-gel oxide film. This is a process recently developed for creation of grating-like features on optical fibers and waveguides, and is now being scaled to dimensions relevant for OSC device processing.


There are new strategies for producing titanyl phthalocyanine (TiOPc) and C60 heterojunctions. After deposition the material can be solvent annealed resulting in nanotexturing and tunability in the NIR.

TiOPc
Solvent annealing protocols.jpg

See Armstrong [1]

References

  1. ↑ N. R. Armstrong et al., Adv. Funct. Mater.  ; DOI: 10.1002/adfm.200801723


Previous Topic Return to OPV Menu
Retrieved from "http://cleanenergywiki.org/index.php?title=Current_OPV_Research_Directions&oldid=4849"